Dimple Dies

These are the best quality made in the USA dimple dies available. These four crater maker dies are CNC machined from 4140 alloy steel, heat-treated for hardness, Sizes are #10, 1/4", 5/16" and 3/8". The #10 uses a dowel pin to align the dies while the others use threaded bolts. The 5/16 and 3/8 bolts can be used to draw the dies together however this hardware is not meant to last forever. We recommend using the provided hardware as alignment pins or starting bolts and finishing the operation with a large bench vice or hydraulic press. The Crater Makers require a lot of force, much more than some of our other dies. Use Anti-Seize or other lube to prevent galling of threads and dies!

This is the best quality made in the USA dimple die available. Need to add a little bit of detail to your work? Drill or punch a 1/4” hole where you would like this detail then use either an impact hammer (air or cordless) or a hydraulic press to drive these dies together and form a unique "Crater" in your panel. These dimple dies are made from 4140 alloy steel and then hardened and tumbled for a smooth finish. Dimensions are 1.5" diameter by approximately 1" combined height. These dies have been tested on 22, 20, and 18ga mild steel. 18 gauge mild steel is the maximum capacity. Each kit comes with a grade 8 hardened nut and bolt for die alignment.(NOTE) The final hole size will naturally end up slightly larger than the 1/4” that it started out as. This is normal and you should plan on using a flanged bolt or a washer with your fastener. Anti-seize should be used on threads and forming surfaces to prevent galling and it also aids in the removal of dies from the panel. Some distortion will occur to your panel, therefore either some pre-stretching of the area may be required, and/or correction to the surrounding area may be needed depending on the metal type, thickness, and application.

These are the best quality made in the USA dimple dies available. These dies are designed to recess the flange of a riv nut in a sheet metal panel. This allows you to bolt two panels together without the obstruction of a riv nut head. These dies are CNC machined from 4140 Pre-hard alloy steel. These all have 1/4-20 threads on the female die. Drill a 1/4" hole in your panel, install the dimple, then drill the 1/4" hole out to the proper size for the desired riv nut. De-burr and install the riv nut. NOTE: *A step bit or uni-bit works best for getting closer to your final hole size. This will keep the hole centered with the dimple. *Can be installed with a bolt but works best when installed with our HF-D100 hydraulic installation tool with 3750 lbs of pull force. Installation tool not included!

This is the best quality made in the USA dimple die available. This #10 Crater Maker is the little brother to our 1/4" Crater Maker. CNC machined from 4140 alloy steel and heat-treated for hardness. These dimple dies to press a unique detail around your #10 fasteners on your inner fenders, engine compartment, or another attachment area that needs a little strength and style. Comes with an alignment pin for installation with a vise or press. Works great with button heads, 12pt fasteners, and socket cap screws. Note: *do not press on alignment pin* Made in the USA

It's challenging to add accessory knobs and switches to your metal dash and retain an OEM look. We've solved that for you.The Apache Die is the easiest way to add Accessory knobs, HVAC knobs, Radio knobs to your dash while retaining a factory look. These dies are simple to install. Start by drilling a 3/8" hole, insert the supplied bolt through the hole, tighten the Apache Die. Done. Your switch will be perfectly centered with no measuring.We designed the die to replicate 55-59 Chevrolet dash dimples. However, they’ll replicate anything you want to do with a 1” ID and 1.875” OD”. Applications are endless. Made in Texas USA from 4140 Heat Treated Steel.

This is the best quality made in the USA dimple die available. This 5/16” Crater Maker is the little brother to our 3/8" Crater Maker. Use these dimple dies to install a unique detail around your fasteners on your inner fenders, engine compartment, or other attachment area that needs a little strength and style. Comes with grade 8 bolt and nut for installation with an impact gun. Can also be installed with a hydraulic press. Works great with button heads, 12pt fasteners and socket cap screws. Made in USA NOTE: *Do not press on bolt *If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

These are the best quality made in the USA dimple dies available. Raised Recess Dimple Dies are just like the old ones you would see on a car from the thirties. They create a raised bump upward and have a countersunk bottom that is designed to work with standard 82 degree countersunk fasteners. The shape these make allows you to use a countersunk fastener without any clearance issues on the bottom side of your panel. The set comes with #8, #10, 1/4, 5/16, and 3/8. CNC machined from 4140 Pre-hard alloy steel. Made in Texas!

These are the best quality dimple dies available, made in the USA. A complete set of four Flush Recess Dies. Dies are CNC machined from Pre-Hard 4140 alloy steel for long-lasting durability. Sizes are #10, 1/4", 5/16" and 3/8".

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. You choose which kit you want 2, 4, or 6 dies. The larger the diameter, the deeper they get. These particular dies are rated for 16ga mild steel. These dies can be installed with a hydraulic press or large bench vise. Larger dies may be installed with an impact driver. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! 2 die kit comes with 7/16" and 1/2" dies 4 die kit comes with #10, 1/4", 5/16" and 3/8" dies 6 die kit comes with #10, 1/4", 5/16", 3/8", 7/16" and 1/2" dies

Having trouble deciding what fasteners to use and what dimples will work for your project? Maybe you need a sample stamper to help you make a better purchasing decision? We now offer these steel stamped sample cards for you to hang in your shop where all your crew can easily get to them so everyone can make faster, better fabrication decisions! Go!

This is the best quality made in the USA dimple die available. The 3/8” Crater Maker is the first product developed by Hammerfab back in 2014. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

Keep all your Hammer Fab dimple dies neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraved set names and sizes for easy to read selection and stow. Made specifically to stow our dimple dies; Only the following dies listed below come with the set. As the new dies become available they may be purchased individually to add to your collection Flat Recess (6), Apache (3), Crater Maker (6), Raised Recess (5), Flush Recess (4), and Riv Nut Recess (4). Also room for alignment studs for use in press (coming soon for an additional cost) Minimum drawer height required for this insert with Hammer Fab dies is 1.5”. Dimensions of foam are 16.25” wide, 15” long, 1” thick. Other add-on foam inserts for backer pads, clecos, etc will be available soon.

This is the best quality made in the USA dimple die available. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required. Anti-sieze is recommended

Hard case made by Pelican to fit your dimple die sets. Each case comes with the selected 3D printed chassis to keep your dies organized. Foam lid keeps the dies secure while transporting.

Keep all your Hammer Fab dimple dies neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraved set names and sizes for easy to read selection and stow. Select drawer size from drop down menu that best suits your needs. Made specifically to stow our dimple dies; (dies are not included with this product at this time) A “Master Set” will be available soon! Flat Recess, Apache, Crater Maker, Raised Recess, Flush Recess, and Riv Nut Recess Also room for alignment studs for use in press Minimum drawer height required for this insert with Hammer Fab dies is 1.5”. Dimensions are 16.25” wide, 15” long, 1” thick. Other add on foam inserts for backer pads, clevos, etc will be available soon.

This is the best quality made in the USA dimple die available. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 1/2" dies may be installed with an impact driver or hydraulic press. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: 2.3" Dimple inner diameter: 1.7" Dimple outer diameter: 1.95" Dimple depth: .24" Uses:Hood pins, dash knobs, switches, large bolts, panel standoffs, consoles.

These are the best quality made in the USA dimple dies available. These four crater maker dies are CNC machined from 4140 alloy steel, heat-treated for hardness, Sizes are #10, 1/4", 5/16" and 3/8". The #10 uses a dowel pin to align the dies while the others use threaded bolts. The 5/16 and 3/8 bolts can be used to draw the dies together however this hardware is not meant to last forever. We recommend using the provided hardware as alignment pins or starting bolts and finishing the operation with a large bench vice or hydraulic press. The Crater Makers require a lot of force, much more than some of our other dies. Use Anti-Seize or other lube to prevent galling of threads and dies!

Kit includes:1. 7/16 flat recess dimple die2. 4 rubber grommets3. 5/16 Crater Maker washers of color choice - raw stainless, polished stainless, and cerakote black stainless4. 4 raw stainless 5/16 -18 button head bolts5. 4 Lasercut steel tabs (3/16” thick) tapped 5/16-18

Can't decide what to get your loved ones? Get them a Hammer Fab Gift Card and fret no more! Let them choose what they want from our website Once you’ve placed your order you will receive a separate email with the gift card code attached that you can save, share, or print off.

This is a replacement pin for our #10 crater maker dimple die. Just press the old one out and press the new one in.

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 17/16" dies may be installed with an impact driver or hydraulic press. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: 1.85" Dimple inner diameter: 1.36" Dimple outer diameter: 1.55" Dimple depth: .190" Uses: Firewalls, dash knobs, lights, switches, bolts, rubber feet, panel standoff

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 1/4" dies may be installed with a hydraulic press, HF-D100 hydraulic installation tool, or a large bench vise. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: .95" Dimple inner diameter: .7" Dimple outer diameter: .8" Dimple depth: .1" Uses: Firewalls, dash knobs, lights, switches, bolts, rubber feet, panel standoff, engine bays, inner fenders

Hammer Fab is all about metal shaping. If you are a tool junkie like us you have hunted down a Pullmax machine and now you want to deck it out with all the toys. Well, you have come to the right place! This base raises the machine 16" off the ground—about 5-6" higher than stock. We integrated massive tooling storage racks on each side between the legs. If you're serious about metal shaping, you'll need the extra tool space. Get ergonomic and lift your Pullmax to stop hunching over. All parts are CNC laser-cut from HRPO steel and drop-shipped for final welding. The parts are tabbed and slotted for easy welding—you can't get it wrong! The tool trays have stops that bolt onto the back with PEM inserts so your tools don't fall into the abyss. Check the CAD drawing to ensure this fits your machine. Some machines vary slightly, so let us know if we need to make adjustments. It's no big deal. You will be billed separately for shipping. This will come on a pallet.

For situations where stamping your dies in a press or even with an impact is just not an option, we have come up with this solution. Weld these “coupon dimples” into your panel anywhere you want! laser cut from 18ga mild steel. Just twist them out like a model car piece or cut them out with a small air saw. Drill your hole with a hole saw and clamp it in place for welding. Hang the extras on a peg board for easy identification and easy re-ordering. Sold in sets of 8.