Gear from the bench.

Hard case made by Pelican to fit your dimple die sets. Each case comes with the selected 3D printed chassis to keep your dies organized. Foam lid keeps the dies secure while transporting.

It's challenging to add accessory knobs and switches to your metal dash and retain an OEM look. We've solved that for you.The Apache Die is the easiest way to add Accessory knobs, HVAC knobs, Radio knobs to your dash while retaining a factory look. These dies are simple to install. Start by drilling a 3/8" hole, insert the supplied bolt through the hole, tighten the Apache Die. Done. Your switch will be perfectly centered with no measuring.We designed the die to replicate 55-59 Chevrolet dash dimples. However, they’ll replicate anything you want to do with a 1” ID and 1.875” OD”. Applications are endless. Made in Texas USA from 4140 Heat Treated Steel.

These are the best quality made in the USA dimple dies available. These four crater maker dies are CNC machined from 4140 alloy steel, heat-treated for hardness, Sizes are #10, 1/4", 5/16" and 3/8". The #10 uses a dowel pin to align the dies while the others use threaded bolts. The 5/16 and 3/8 bolts can be used to draw the dies together however this hardware is not meant to last forever. We recommend using the provided hardware as alignment pins or starting bolts and finishing the operation with a large bench vice or hydraulic press. The Crater Makers require a lot of force, much more than some of our other dies. Use Anti-Seize or other lube to prevent galling of threads and dies!

These are the best quality made in the USA dimple dies available. These dies are designed to recess the flange of a riv nut in a sheet metal panel. This allows you to bolt two panels together without the obstruction of a riv nut head. These dies are CNC machined from 4140 Pre-hard alloy steel. These all have 1/4-20 threads on the female die. Drill a 1/4" hole in your panel, install the dimple, then drill the 1/4" hole out to the proper size for the desired riv nut. De-burr and install the riv nut. NOTE: *A step bit or uni-bit works best for getting closer to your final hole size. This will keep the hole centered with the dimple. *Can be installed with a bolt but works best when installed with our HF-D100 hydraulic installation tool with 3750 lbs of pull force. Installation tool not included!

This is the best quality made in the USA dimple die available. This #10 Crater Maker is the little brother to our 1/4" Crater Maker. CNC machined from 4140 alloy steel and heat-treated for hardness. These dimple dies to press a unique detail around your #10 fasteners on your inner fenders, engine compartment, or another attachment area that needs a little strength and style. Comes with an alignment pin for installation with a vise or press. Works great with button heads, 12pt fasteners, and socket cap screws. Note: *do not press on alignment pin* Made in the USA

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. You choose which kit you want 2, 4, or 6 dies. The larger the diameter, the deeper they get. These particular dies are rated for 16ga mild steel. These dies can be installed with a hydraulic press or large bench vise. Larger dies may be installed with an impact driver. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! 2 die kit comes with 7/16" and 1/2" dies 4 die kit comes with #10, 1/4", 5/16" and 3/8" dies 6 die kit comes with #10, 1/4", 5/16", 3/8", 7/16" and 1/2" dies

These are the best quality dimple dies available, made in the USA. A complete set of four Flush Recess Dies. Dies are CNC machined from Pre-Hard 4140 alloy steel for long-lasting durability. Sizes are #10, 1/4", 5/16" and 3/8".

This is the best quality made in the USA dimple die available. Need to add a little bit of detail to your work? Drill or punch a 1/4” hole where you would like this detail then use either an impact hammer (air or cordless) or a hydraulic press to drive these dies together and form a unique "Crater" in your panel. These dimple dies are made from 4140 alloy steel and then hardened and tumbled for a smooth finish. Dimensions are 1.5" diameter by approximately 1" combined height. These dies have been tested on 22, 20, and 18ga mild steel. 18 gauge mild steel is the maximum capacity. Each kit comes with a grade 8 hardened nut and bolt for die alignment.(NOTE) The final hole size will naturally end up slightly larger than the 1/4” that it started out as. This is normal and you should plan on using a flanged bolt or a washer with your fastener. Anti-seize should be used on threads and forming surfaces to prevent galling and it also aids in the removal of dies from the panel. Some distortion will occur to your panel, therefore either some pre-stretching of the area may be required, and/or correction to the surrounding area may be needed depending on the metal type, thickness, and application.

This is the best quality made in the USA dimple die available. This 5/16” Crater Maker is the little brother to our 3/8" Crater Maker. Use these dimple dies to install a unique detail around your fasteners on your inner fenders, engine compartment, or other attachment area that needs a little strength and style. Comes with grade 8 bolt and nut for installation with an impact gun. Can also be installed with a hydraulic press. Works great with button heads, 12pt fasteners and socket cap screws. Made in USA NOTE: *Do not press on bolt *If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

This is the best quality made in the USA dimple die available. The 3/8” Crater Maker is the first product developed by Hammerfab back in 2014. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

Get the inside scoop on our Metal Finishing seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how-to, however, it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

In this PDF you can see and learn many of the steps in chopping a “turret” style chop. The methods in this book would apply to cars from the late 1930’s up until the late 1950’s. Some cars that are famous for this look are lead sled mercs, shoebox fords, chevy bel airs, oldmobiles, and many others. This style of chop is usually performed on 2 door sedans and 2 door coupes.

Get the inside scoop on our Floorpan Fabrication seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how to, however it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

Get the inside scoop on our Compound Curves seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how-to, however, it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

Get the inside scoop on our Wheel Tub Fabrication seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how to, however it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

In this lengthy PDF download you will learn not only how to shape copper into a killer bull skull but also all the techniques and processes of how to make the mold, buck, patterns, and hammer form for shaping the metal. This one is packed with lots of valuable information.

Get the inside scoop on our Firewall Fabrication seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how-to, however, it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

These backing pads are available in 4 different sizes - 3/4"(New), 1”, 2” and 3”. We at Hammerfab have designed these backing pads with several unique features in mind.• Constructed of durable nylon• Always keeps the disc flat• Lightweight• Thin outer edge• 1/4” steel arbor that fits your tool• Dimples for better grip when removing•3/4" backing pad is constructed of 3D printed stainless steel

Hammerfab designed this ULTRA FLEX 3 inch rubber backing pad for Roloc style disks with various unique features. Our backer ensures your abrasive disk stays flat throughout use, unlike other brands that lose their shape over time. Made of durable, flexible rubber, it is also sturdy enough to maintain its shape. This high-quality FLEX backer has passed multiple drop tests from over 12 feet, even when installed on an air tool. Its 1/4" stainless steel arbor fits most tools, while the dimples on the backside provide better grip when removing disks. Available in black.

Maintain consistent radii over the entire length of your workpiece. Save the wear on your burr grinders and increase your profit margins as you cut your metal finishing time. Give a Radi Backer a try. You’ll never look back!

This Gapper Pad is designed by Hammerfab to help you get those door gaps set to the desired gap for a crisp, clean look. We chose the most common sizes, 1/8", 3/16", and 1/4". (These measurements include the thickness of a 3M Greencorp 50grit Roloc disc attached to the backer. Thickness may vary depending on which style or brand of discs you are using). It has the same 1/4" steel arbor as our 3" Backer Pads. Dimples on the backside are there for better grip while removing disks.

These bead rolling "Tipping" dies are designed by Hammerfab for tipping or turning a flange on a sheet metal panel. When you need to make a curved bend, bolt on this tipping die. Tip a curved flange on a fender or door skin. Use it for tipping a perfectly straight line if you don't have a sheet metal break. These dies are also great for "crisping" an already existing bend or body line. Made in Texas from 4140 pre-hardened alloy steel and then CNC machined for precision. These dies will fit any bead roller that has 3/4" shafts and 1" thick dies.

These bead rolling "Tipping" dies are designed by Hammerfab for tipping or turning a flange on a sheet metal panel. When you need to make a curved bend, bolt on this tipping die. Tip a curved flange on a fender or door skin. Use it for tipping a perfectly straight line if you don't have a sheet metal break. These dies are also great for "crisping" an already existing bend or body line. Made in Texas from 4140 pre-hardened alloy steel and then CNC machined for precision. These dies will fit any bead roller that has 3/4" shafts and 1" thick dies.

These bead rolling "Tipping" dies are designed by Hammerfab for tipping or turning a flange on a sheet metal panel. When you need to make a curved bend, bolt on this tipping die. Tip a curved flange on a fender or door skin. Use it for tipping a perfectly straight line if you don't have a sheet metal break. These dies are also great for "crisping" an already existing bend or body line. Made in Texas from 4140 pre-hardened alloy steel and then CNC machined for precision. These dies will fit any bead roller that has 3/4" shafts and 1" thick dies.

These bead rolling "Tipping" dies are designed by Hammerfab for tipping or turning a flange on a sheet metal panel. When you need to make a curved bend, bolt on this tipping die. Tip a curved flange on a fender or door skin. Use it for tipping a perfectly straight line if you don't have a sheet metal break. These dies are also great for "crisping" an already existing bend or body line. Made in Texas from 4140 pre-hardened alloy steel and then CNC machined for precision. These dies will fit any bead roller that has 3/4" shafts and 1" thick dies.

The HF-D100 Hydraulic Installation tool is a must for any serious fabricator. This tool is very versatile as it can be used for installing dimple dies, riv nuts, and also for punching holes if you have the proper dies. It is hand operated with a pump-action and has an easy access button for releasing the pressure. Comes with 1/4-20 mandrel and hard plastic case. Additional mandrels are sold separately. 3750 lbs of pull force are perfect for the riv nut recess dies, riv nuts, flush recess dies (requires the additional mandrels sold separately) or anything requiring 3750 lbs of force or less. Crater makers require too much force for this tool.

Use this vise clamp to protect your anodized or polished A/N fittings while building custom fuel lines. These -6 and -8 A/N sizes are the most common for fuel lines for vehicles demanding up to 750 HP! Color will be BLACK!

Our assembly hammer is a must-have tool for detailed assembly work on high-end projects. Whether you need to lightly tap in some neodymium magnets, a polished stainless fastener, nudge some precious glass, or persuade chrome into place, this soft lightweight hammer will do the trick. The hammer features a 3D-printed head and handle. Both head and handle are made from the same rugged nylon as our Backer and Gapper pads. All have proven to be tough around the shop. The assembly hammer handle is 8 inch stainless steel or 12 inch solid aluminum for a rigid hit yet light for control-ability. The handle has a grenade-like grip with a hole for hanging or wrist lanyard. Made in the USA!

These mandrels are for our HF D100 hydraulic installation tool. Used for installing Riv nuts as well as some of our dimple dies. Choose the size you need. Sold individually.

Is it time to eliminate your tailgate chains or even those unsightly scissor holds or cables? We have developed this clean, trick alternative to keeping your tailgate flat while open but also keep your friends scratching their heads. They are laser cut from 1/2” thick steel and come pre drilled and tapped along with the proper stainless hardware for installation. just cut a small rectangular slot in the bottom of your tailgate, drill a few holes, bolt these on and bam, you can eliminate your chains, cables, and scissor holds. These are universal but are guaranteed to work with ‘59-‘66 GM Fleetside tailgates.

These billet latches allow you to eliminate your old clangy chains. No more scratching your paint job or beautiful patina. These utilize the original chain mounting points both on the tailgate and on the bed end cap. You will need to re-tap the bed hole to 1/2-13 threads and drill the hole on the tailgate tab out to 1/2”. That’s it! Then bolt these bad boys on for a stylish look. The kit comes with some trick stainless hardware which is what helps make this a clean install. The push-button pins are stainless as are the 1/2-13 receptacles. The billet aluminum latches swing out of the way on a 316 stainless steel shoulder bolt with a pre-installed threaded insert. Also included are two tailgate stops “Flippers” which eliminate your tailgate chains and those unsightly scissor holds or cables. They can be installed on the bottom edge of your tailgate with minimal cutting and drilling and hold your tailgate open at a 90 degree angle. When installed correctly you won’t even be able to see them. The stops are laser cut from 1/2” thick steel and come pre-drilled and tapped and also come with the necessary stainless hardware and instructions. Available in raw billet aluminum (no measurable machining marks) basically they are smooth but look really cool. Sold as a matching pair. Two Styles: Streamline/Smooth or Arch/Recessed Pocket Download InstructionsWatch Installation Video

Strip Tabs metal strips have been laser cut with precision so that you don't have to figure out all the spacing of your holes. Smooth laser cut edges don't need sanding! These strips can be welded to your roll cage, window opening, or even butt welded directly to a flat panel to appear as if it was always part of that panel. Available in the following materials and thicknesses. Strips are approximately 36" long. 18ga mild steel (may have slight signs of rust from shipping) 16ga mild steel (may have slight signs of rust from shipping) 14ga mild steel (may have slight signs of rust from shipping) 18ga stainless steel 16ga stainless steel 14ga stainless steel *other metals and thicknesses may be available upon request.

Crater Maker Washers are designed to complement our Crater Maker Dimple dies. The washers give a "bolt-on" detail. The washers will match our Dimple Dies exactly. The washers are stamped out of laser-cut 18ga Stainless Steel. We individually polish and package each stainless crater. You’ll receive a perfectly polished piece saving you hours of polishing work. The edge of the washer sits off the panel at the center the washer makes contact. If your paint or polished surface is marred it will be hidden. These are designed to work with the most common fasteners such as button heads, ARP, and Socket cap style screws. All washers come as a set of 10. The washers are available in raw, polished, and Cerakote black finishes. (Cerakote parts are done in lots so different lots may vary in color and sheen) All designed, manufactured, and packaged in the USA!

These quick attachment lugs, a Hammer Fab exclusive are a great way to mount, hang, attach, or latch components on your hot rod, custom car, or bike. The final result is a clean look both when the component is attached and when it is removed. No special tools are required to remove the panels using this system. A firm pull and the panel will pop off. The lugs can be bolted to a panel from the backside using a machine screw or welded on the stud. These lugs can be used to hang components vertical on a frame rail, or interior panel, or horizontal for an engine cover, etc. Specs: Lug3/4" diameterTALL Shoulder- 5/8" height overall 1/4” shoulder SHORT Shoulder- 1/2” height overall 1/16” shoulder 1/4-20 female threads x1/2" deep for tall shoulder lug 1/4-20 female threads for short shoulder lugGrommets Install tip Drill a 17/32" hole for proper grip, 1/2” for a tight fit DOES NOT INCLUDE GROMMETS Sold Individually

Protect your suspension air bags by limiting the amount of axle or control arm travel. You will need to supply the nylon webbing and sew them to the correct length. Can be used for other applications. Width: 1.75”Height: 2.3”Thickness: 11 GaugeEyehole: 7/16” or 9/16”Strap Slot: 1”x.25”Material: Stainless 304

THIN GROMMETS BLK : 1/16” MATERIAL THICKNESS HIGH TEMP ORANGE: 1/16” MATERIAL THICKNESS THICK GROMMETS BLK: 1/8” MATERIAL THICKNESS

These C10 tees are made from 100% cotton lightweight Anvil T shirts. They are printed in the USA. Artwork by Problem Child Customs to represent one of our current builds.

4.3 oz., preshrunk 100% combed ringspun cotton. Fits true to size. Softest Short Sleeve available.

4.3 oz., preshrunk 100% combed ringspun cotton. Fits true to size.

Not only will you look good, you’ll stay warm and toasty with this heavy blend hoodie. Material 50% preshrunk Soft Cotton, 50% polyester

Kit includes:1. 7/16 flat recess dimple die2. 4 rubber grommets3. 5/16 Crater Maker washers of color choice - raw stainless, polished stainless, and cerakote black stainless4. 4 raw stainless 5/16 -18 button head bolts5. 4 Lasercut steel tabs (3/16” thick) tapped 5/16-18

Looking to install a custom stainless exhaust with a clean and precise fit? Our 1/8" stainless steel hangers, available in 2.5" and 3" OD tubing, are laser cut for a perfect fit. Use our blue/black/orange high temp grommets (sold separately) for optimal performance. These hangers are used on all builds at Hammerfab and can be paired with our crater maker raw washer kit for a complete look. Type 1 - Flat Straight Type 2- Flat Offset Type 3- Round Offset Type 4- Round Straight

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 17/16" dies may be installed with an impact driver or hydraulic press. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: 1.85" Dimple inner diameter: 1.36" Dimple outer diameter: 1.55" Dimple depth: .190" Uses: Firewalls, dash knobs, lights, switches, bolts, rubber feet, panel standoff

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 1/2" dies may be installed with an impact driver or hydraulic press. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: 2.3" Dimple inner diameter: 1.7" Dimple outer diameter: 1.95" Dimple depth: .24" Uses:Hood pins, dash knobs, switches, large bolts, panel standoffs, consoles.

These laser cut steel mounts are just what you need to convert your LS engine to an old school style three bolt rubber engine mount. These offset your LS engine as far back on the block as possible without hitting the castings on the block. They come with the necessary metric hardware (stainless) for mounting to your block. Available in raw steel and powder coated black Urethane Engine mount option coming soon!

These are the best quality made in the USA dimple dies available. Raised Recess Dimple Dies are just like the old ones you would see on a car from the thirties. They create a raised bump upward and have a countersunk bottom that is designed to work with standard 82 degree countersunk fasteners. The shape these make allows you to use a countersunk fastener without any clearance issues on the bottom side of your panel. The set comes with #8, #10, 1/4, 5/16, and 3/8. CNC machined from 4140 Pre-hard alloy steel. Made in Texas!

Keep your sheet metal panels in place with Clecos. Clecos have been around for decades. They were invented for holding airplanes together prior to installing thousands of rivets. When riveting it is very crucial that every single hole lines up perfectly so why not apply that technique to building hot rods? These packs of 10, 50 and 100 give you plenty to work with for small to large panels. You may also be interested in our Cleco starter kits which come with pliers and several sheet metal alignment tabs.

Get the inside scoop on our Engine Bay Fabrication seminar by downloading these “cliff notes” from that class. This in-depth PDF is not a step-by-step how to, however it is loaded with lots of great tips and tricks that we teach in our classes. If you can’t make it to one of our seminars then this is the next best thing. You’ll receive a download link in your purchase order confirmation email.

Download this PDF instructions for our Tailgate Stops

Weld this 3/8” thick steel pad to your floor pan and bolt your GM style dimmer switch to it from the top side. This eliminates the need for bolts to pass through your floor and also eliminates the need for Riv nuts. It also supports the plug to prevent failure. Comes with 1/4-20 threads pre installed. Laser cut in the USA! - switch and screws not included -

Kit includes:1. 7/16 flat recess dimple die2. 4 rubber grommets3. 5/16 Crater Maker washers of color choice - raw stainless, polished stainless, and cerakote black stainless4. 4 raw stainless 5/16 -18 button head bolts5. 4 Lasercut aluminum tabs (3/16” thick) tapped 5/16-18. Weld these to your aluminum panel.

These tailgate stops allow you to eliminate your clangy, scratchy, noisy, rusty chains! Install these into your stock tailgate with minimal modification. They are a semi-bolt on product (you will need to cut slots in the bottom of your tailgate and back of rear bed sill in order to fit and work. Also you will need to countersink the hole (or drill first if you don’t have one) so that the supplies fastener sits flush behind the stock tailgate hinge. Laser cut from 1/2” thick steel these are plenty sturdy enough to support your tailgate but we do not recommend standing or sitting on the tailgate due to the increased leverage applied to the tailgate. Sold as raw steel with stainless hardware and stainless locking plate. install these first and then install the tailgate as a whole unit. Designed to hold the tailgate open at 90 degrees. Stops should contact on the bottom of the rear bed sill when open. If not, you may need to modify (tune) the stopping contact area. *fabrication requiredlight cutting on tailgate and rear bed sill countersinking main mounting hole on tailgate no welding required but you may weld them on if you want to.

Keep your wires organized and easily accessible with our heavy duty wall mount racks. These are laser cut and CNC bent from 10ga steel. They will come with a satin black powder coat finish. *Price is for one pair (one left bracket and one right bracket only) The brackets will be drop shipped to you from Our manufacturer in Wisconsin. Kit will include one left and one right wall brackets. Optional: 6 wall anchor screws, 4 aluminum dowel rods (2’ long each), 8 shaft collars. (Sold separately from brackets and ship separately) These are special order items and will take 2-4 weeks for delivery. Price includes shipping to continental US only!

Keep all your Hammer Fab dimple dies neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraved set names and sizes for easy to read selection and stow. Select drawer size from drop down menu that best suits your needs. Made specifically to stow our dimple dies; (dies are not included with this product at this time) A “Master Set” will be available soon! Flat Recess, Apache, Crater Maker, Raised Recess, Flush Recess, and Riv Nut Recess Also room for alignment studs for use in press Minimum drawer height required for this insert with Hammer Fab dies is 1.5”. Dimensions are 16.25” wide, 15” long, 1” thick. Other add on foam inserts for backer pads, clevos, etc will be available soon.

Keep all your Hammer Fab dimple dies neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraved set names and sizes for easy to read selection and stow. Made specifically to stow our dimple dies; Only the following dies listed below come with the set. As the new dies become available they may be purchased individually to add to your collection Flat Recess (6), Apache (3), Crater Maker (6), Raised Recess (5), Flush Recess (4), and Riv Nut Recess (4). Also room for alignment studs for use in press (coming soon for an additional cost) Minimum drawer height required for this insert with Hammer Fab dies is 1.5”. Dimensions of foam are 16.25” wide, 15” long, 1” thick. Other add-on foam inserts for backer pads, clecos, etc will be available soon.

Having trouble deciding what fasteners to use and what dimples will work for your project? Maybe you need a sample stamper to help you make a better purchasing decision? We now offer these steel stamped sample cards for you to hang in your shop where all your crew can easily get to them so everyone can make faster, better fabrication decisions! Go!

Keep your Backer Pads organized with these foam drawer liners. Dimensions are 4.5”X 15” x1”. Minimum drawer height requires is 2” with backer pads installed. Available for Backer Pads, Gapper Pads, and Radi Backers. They also have a spot for a two inch backer and a one inch backer and a slot to hold your air tool wrenches. Backer Pads sold separately or as bundles (see related products).

For situations where stamping your dies in a press or even with an impact is just not an option, we have come up with this solution. Weld these “coupon dimples” into your panel anywhere you want! laser cut from 18ga mild steel. Just twist them out like a model car piece or cut them out with a small air saw. Drill your hole with a hole saw and clamp it in place for welding. Hang the extras on a peg board for easy identification and easy re-ordering. Sold in sets of 8.

Keep all your Clecos and related accessories neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraving. Clecos and pliers can be purchased separately. A “Master Set” will be available soon! Large tray holds up to 160 Clecos, 9 squeeze clamps, 2 Cleco pliers. The 4 small compartments are intended to keep your specific drill bits separated. Put your HammerFab Cleco tabs in the remaining compartment. Small try holds 36 Clecos, 4 squeeze clamps, and 1 Cleco pliers. Put your Hammer Fab Cleco tabs in the remaining compartment. Minimum drawer height required for this insert with Clecos is 2.5”. Dimensions for large tray are 16.25” wide, 15” long, 1” thick. Dimensions for small tray are 15” long, 6” wide, 1” thick. Other add on foam inserts for backer pads, etc will be available soon.

Kit comes with the following items: (Large) 20-3/32” Clecos, 20-1/8” Clecos, 20-5/32” Clecos, 20-3/16” Clecos, 1-Cleco pliers, 6-Squeeze clamps, 1-large foam drawer liner. (Small) 8-3/32” Clecos, 8-1/8” Clecos, 8-5/32” Clecos, 8-3/16” Clecos, 1- Cleco pliers, 4-Squeeze clamps, 1-small foam drawer liner. Keep all your Clecos and related accessories neatly organized with this 1” thick dual color foam insert. CNC machined in house with laser engraving. Large tray holds up to 160 Clecos, 9 squeeze clamps, 2 Cleco pliers. The 4 small compartments are intended to keep your specific drill bits separated. Put your Hammer Fab Cleco tabs in the remaining compartment. Small tray holds 36 Clecos, 4 squeeze clamps, and 1 Cleco pliers. Put your Hammer Fab Cleco tabs in the remaining compartment. Minimum drawer height required for this insert with Clecos is 2.5”. Dimensions for large tray are 16.25” wide, 15” long, 1” thick. Dimensions for small tray are 15” long, 6” wide, 1” thick. Other add on foam inserts for backer pads, etc are also available.

Use this tool to install cleco clamps.

This is a replacement pin for our #10 crater maker dimple die. Just press the old one out and press the new one in.

Not only will you look good, you’ll stay warm and toasty with this heavy blend hoodie. Material 50% preshrunk Soft Cotton, 50% polyester

We designed these wheel stands with versatility in mind. If you are going to spend this kind of money on a shop tool it better do a lot! Well these do a lot!! We design products that we would use around our shop usually because all the other options are either inadequate or they just don't exist. You can buy these as a "U-Weld-It" kit or we can fully TIG weld them and powder coat them. *Casters only come with the We-Weld-It & Powder coat it kit. You may also buy the casters separately if you choose from the drop down menu. U-weld-it kits will ship directly from the manufacturer in Wisconsin and all kits are made to order so please be patient when ordering. We will update you with tracking info and status updates. *If you'd like the casters they are heavy duty, corrosion resistant, non-locking, polyurethane with roller bearings. They are not cheap! They must withstand the weight of a vehicle and the ones we sell do! The casters we sell are engineered to be able to effortlessly push a vehicle across a smooth shop floor without marring the floor. *Uprights may be MIG or TIG depending on the situation. Either way they will be stout. Our wheel stands do several things: 1- they can be used as wheel stands, for putting your car on with wheels and tires installed. 2- they can be used without wheels and tires (with accessory hub adapter uprights) and bolt directly to your hubs and axles (bolt patters: 5x4.5, 5x4.75, 5x5) 3- with accessory caster plates they can be rolled around a smoother floor with a car bolted to the accessory hub adapters (rolling with tires resting can be done but also dangerous and should only be done in short distances slowly as car could potentially slide off if precautions aren't taken). 4- the wheel stands have 2x2" square holes cut in them which can serve as temporary crossmember slide mounts. This is great for mocking up rear ends or engines in jig type form while the car is elevated on the wheel stands. This is a safe way to fabricate if you don't have a lift in your shop. These holes can also be used for mounting temporary scaffolding for sanding or mechanic work (you make it), or other fixtures. 5- use a low profile floor jack to slide under the center section for installing caster plates or if you just want to raise them up a bit more. 6- the stands are easily stowed. when laid sideways they can be stacked on top of each other. You could also make a custom rack our of 2x2" tubing to hang them on the wall.

Can't decide what to get your loved ones? Get them a Hammer Fab Gift Card and fret no more! Let them choose what they want from our website Once you’ve placed your order you will receive a separate email with the gift card code attached that you can save, share, or print off.

3400 series battery hold down tray. Bolts to any flat surface. Works with common 3400 series batteries of your choice. Grabs the battery from the bottom so no hold down is needed over the top. This helps prevent clutter and unwanted accidental arcing on the battery terminals. Veye sturdy laser cut steel. Comes with stainless mounting hardware. 5/16 - 18 x 1”

Beefy steel angle bracket for frame mounting your 3400 series battery of your choice! This is for the angle bracket only. The hold down tray is sold separately. Very sturdy laser cut steel. *Bolts directly to Choppin Block chassis.

**Introducing Exhaust Fab Blocks by Hammer Fab** Upgrade your exhaust fabrication process with our innovative Exhaust Fab Blocks. Designed to streamline installation and ensure precision, these blocks are a must-have tool for any custom exhaust project. **Features:** - **Accurate Positioning:** Say goodbye to trial and error. Our Exhaust Fab Blocks help you accurately position your exhaust tubing, minimizing waste and saving you time. - **Infinite Adjustability:** Crafted from standard 1”x1/4” thick solid bar stock, the slotted edge design allows for quick iterations and infinite adjustability, translating to faster fabrication. - **Durable Construction:** Made from durable carbon fiber-infused plastic, our blocks are built to withstand the rigors of exhaust fabrication, ensuring longevity and reliability. - **Convenient Design:** Each block is designed to securely snap over the tubing and comes with a steel hanger bar for added convenience during installation. **Versatile Use:** Whether you're a professional fabricator or a DIY enthusiast, our Exhaust Fab Blocks make exhaust building a more pleasant experience. Sold individually or as a set, they're suitable for various applications and projects. **Why Choose Exhaust Fab Blocks?** Even if you only tackle one exhaust system in your lifetime, our blocks will make the job easier and more efficient. Invest in quality tools that enhance your craft and elevate your results. **Shop Now:** Ready to revolutionize your exhaust fabrication process? Browse our selection of Exhaust Fab Blocks and take the first step towards easier installations and professional results.

This is the best quality made in the USA dimple die available. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required.

This is the best quality made in the USA dimple die available. It is CNC machined from 4140 alloy steel and then heat-treated for hardness. Install with a hydraulic press, bench vice, or an impact gun using the nut and bolt included with the kit. Rated for 18 gauge mild steel (cold finish) max. NOTE: Do not press on the bolt If using an impact gun the bolt will only withstand the tensile strength for a few installations. Additional bolts will be required. Anti-sieze is recommended

These are the best quality made in the USA dimple dies available. Flat Recess Dimple Dies are great for making a fastener sit just a little bit below the surface of your panel or flip it over and it can be just a little higher than your panel. These add substantial strength to the panel as well as a clean, detailed look. These particular dies are rated for 16ga mild steel. These 1/4" dies may be installed with a hydraulic press, HF-D100 hydraulic installation tool, or a large bench vise. Dies are CNC machined from 4140 heat-treated steel. Made in Texas! Specs: Die outer diameter: .95" Dimple inner diameter: .7" Dimple outer diameter: .8" Dimple depth: .1" Uses: Firewalls, dash knobs, lights, switches, bolts, rubber feet, panel standoff, engine bays, inner fenders

Introducing our new Harness/Hose Hangers – the ultimate solution for keeping your wire harnesses and air conditioning/heater hoses neatly organized and out of harm's way. Designed to fit a wide range of applications, these hangers are crafted with convenience and durability in mind.Constructed from high-quality ABS plastic via state-of-the-art 3D printing technology, these hangers are built to withstand the elements, ensuring long-lasting performance. With a sleek satin black finish, they seamlessly blend into any engine bay or inner fender.Each hanger features 5/16 fasteners, commonly found in automotive settings, for easy installation. Plus, stainless hardware is included, ensuring a secure fit every time. Whether you need one, a pair, or a set of four, we offer flexible purchasing options to suit your needs.Please note that while these hangers may have minimal visible print lines, they are designed to maintain a clean and tidy appearance. Surface variations may occur when ordering multiples, but rest assured, their functionality remains un compromised. For those looking to customize further, these hangers can be vapor smoothed or painted to match your vehicle's aesthetic. The choice is yours – keep it sleek or unleash your creativity. Upgrade your organization game today with our Harness/Hose Hangers and say goodbye to cluttered engine bays. Keep your essentials tidy and ready for action.

AVAILABLE FOR PRE-ORDER ONLY AT THIS TIME Once we receive 5+ preorders we will then manufacture these all at once Modern engines may not always be the most visually appealing, but their impressive power certainly compensates for it. Now, you can enhance both performance and aesthetics with our exquisite billet stainless steel (304) header flanges, designed for those who refuse to settle for mediocrity. These flanges feature a 1-7/8” bore for round tubing on the outside and a similar D-shaped bore on the inside, ensuring optimal flow for serious boost. The back side is meticulously machined with integrated raised “boost seals” around each port, designed to embed into the included laser-cut copper gaskets, which are perfectly port-matched to the flanges. It's up to you whether to port match your heads to these flanges. Crafted for durability, these flanges are 3/8” thick on the flat parts and .810” thick at the tallest point of each port hole. Each bolt hole is reinforced with a raised boss to add thickness and distribute the load evenly when torquing down the flanges. The provided stainless steel flanged bolts come with serrated knurls on the backside to prevent unwanted loosening. Anti-seize is highly recommended when installing to prevent galling of threads. Proudly made in Texas, these flanges are guaranteed to have less than .002” deflection when placed on a granite surface. Each set is shrink-wrapped to a cardboard backer to ensure safe delivery without any damage. *Note: For those who prefer a polished finish, some sanding may be required to remove tool marks around each port, although the surface is already very smooth.

These are the popular Richardson 112 adjustable trucker hats. They fit great and look great! Hammer Fab logo has been embroidered.

These Chevelle tees are made from 100% cotton. They are screen printed in the USA. Artwork by Graphic Disorder to represent one of our current builds. Garment is Gildan Softstyle 980 100% cotton (kinda stretchy and light)

Our Billet Tailgate Hinges are expertly crafted from CNC machined aircraft grade aluminum and include stainless steel hardware and bronze oil-lite bushings for precise and smooth operation. These hinges are designed with a 2.5" raised bed floor in mind, ensuring a flush fit for your tailgate. While installation may require some fabrication, our detailed instructions will assist you in completing the process with ease. Please note, bump stops are necessary and latches are not included, but can be purchased here. Note: These can also be used as a universal hinge. We have used them for tilting pickup truck bed floors which works well.

Nuke Performance Black Nylon AN Braided Fuel Hose Nuke Performance offers a wide selection of fuel hose and hose ends. The Full Flow AN series is ready for all types of motorsports applications and is safe for all types of fuel, including alcoholic fuels such as ethanol. Black Nylon braided nitrile fuel hose with stainless steel braiding The AN fuel hose from Nuke Performance is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Currently you can get it in 20 ft lengths from Hammer Fab.

Nuke Performance Full Flow AN Hose Ends We offer a careful selection of Hose Ends to be used in combination with our complete range of high-performance fuel upgrade parts. CNC-machined and hard anodized for a long-lasting, corrosion-free appearance and function. Designed to stand up to the destructive properties of alcohol fuels, including ethanol and methanol. The Full Flow series is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Full Flow, Nuke Performance premium AN hose ends, for all types of motorsport applications. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Ethanol approved high quality, lightweight, full flow hose end fittings for nitrile fuel hose. Nuke Performance offers a wide range of hose ends. With the AN lineup, you get a perfect solution for all types of fuels. Wide variation and in various sizes. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12 For Nuke Performance Full-Flow AN fuel hose Full Flow hose ends for motorsports applications Straight / 30 / 45 / 60 / 90 / 120 / 150 / 180 degree Safe for all type of fuels, including ethanol The Nuke Performance Full Flow series offers AN hose ends and a premium black nylon race hose which is reinforced with a single braid of bright, corrosion-resistant type 302 stainless steel wire braid, and the black braided nylon cover makes this lightweight hose both durable and attractive. Safe for alcoholic fuels, but for long-time use you should look into the Nuke Performance Full Flow PTFE series with a much longer life span when used with alcoholic fuels such as ethanol.

Nuke Performance Full Flow AN Hose Ends We offer a careful selection of Hose Ends to be used in combination with our complete range of high-performance fuel upgrade parts. CNC-machined and hard anodized for a long-lasting, corrosion-free appearance and function. Designed to stand up to the destructive properties of alcohol fuels, including ethanol and methanol. The Full Flow series is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Full Flow, Nuke Performance premium AN hose ends, for all types of motorsport applications. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Ethanol approved high quality, lightweight, full flow hose end fittings for nitrile fuel hose. Nuke Performance offers a wide range of hose ends. With the AN lineup, you get a perfect solution for all types of fuels. Wide variation and in various sizes. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12 For Nuke Performance Full-Flow AN fuel hose Full Flow hose ends for motorsports applications Straight / 30 / 45 / 60 / 90 / 120 / 150 / 180 degree Safe for all type of fuels, including ethanol The Nuke Performance Full Flow series offers AN hose ends and a premium black nylon race hose which is reinforced with a single braid of bright, corrosion-resistant type 302 stainless steel wire braid, and the black braided nylon cover makes this lightweight hose both durable and attractive. Safe for alcoholic fuels, but for long-time use you should look into the Nuke Performance Full Flow PTFE series with a much longer life span when used with alcoholic fuels such as ethanol.

Nuke Performance Full Flow AN Hose Ends We offer a careful selection of Hose Ends to be used in combination with our complete range of high-performance fuel upgrade parts. CNC-machined and hard anodized for a long-lasting, corrosion-free appearance and function. Designed to stand up to the destructive properties of alcohol fuels, including ethanol and methanol. The Full Flow series is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Full Flow, Nuke Performance premium AN hose ends, for all types of motorsport applications. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Ethanol approved high quality, lightweight, full flow hose end fittings for nitrile fuel hose. Nuke Performance offers a wide range of hose ends. With the AN lineup, you get a perfect solution for all types of fuels. Wide variation and in various sizes. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12 For Nuke Performance Full-Flow AN fuel hose Full Flow hose ends for motorsports applications Straight / 30 / 45 / 60 / 90 / 120 / 150 / 180 degree Safe for all type of fuels, including ethanol The Nuke Performance Full Flow series offers AN hose ends and a premium black nylon race hose which is reinforced with a single braid of bright, corrosion-resistant type 302 stainless steel wire braid, and the black braided nylon cover makes this lightweight hose both durable and attractive. Safe for alcoholic fuels, but for long-time use you should look into the Nuke Performance Full Flow PTFE series with a much longer life span when used with alcoholic fuels such as ethanol.

Nuke Performance Full Flow AN Hose Ends We offer a careful selection of Hose Ends to be used in combination with our complete range of high-performance fuel upgrade parts. CNC-machined and hard anodized for a long-lasting, corrosion-free appearance and function. Designed to stand up to the destructive properties of alcohol fuels, including ethanol and methanol. The Full Flow series is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Full Flow, Nuke Performance premium AN hose ends, for all types of motorsport applications. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Ethanol approved high quality, lightweight, full flow hose end fittings for nitrile fuel hose. Nuke Performance offers a wide range of hose ends. With the AN lineup, you get a perfect solution for all types of fuels. Wide variation and in various sizes. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12 For Nuke Performance Full-Flow AN fuel hose Full Flow hose ends for motorsports applications Straight / 30 / 45 / 60 / 90 / 120 / 150 / 180 degree Safe for all type of fuels, including ethanol The Nuke Performance Full Flow series offers AN hose ends and a premium black nylon race hose which is reinforced with a single braid of bright, corrosion-resistant type 302 stainless steel wire braid, and the black braided nylon cover makes this lightweight hose both durable and attractive. Safe for alcoholic fuels, but for long-time use you should look into the Nuke Performance Full Flow PTFE series with a much longer life span when used with alcoholic fuels such as ethanol.

Nuke Performance Full Flow AN Hose Ends We offer a careful selection of Hose Ends to be used in combination with our complete range of high-performance fuel upgrade parts. CNC-machined and hard anodized for a long-lasting, corrosion-free appearance and function. Designed to stand up to the destructive properties of alcohol fuels, including ethanol and methanol. The Full Flow series is available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Full Flow, Nuke Performance premium AN hose ends, for all types of motorsport applications. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12. Ethanol approved high quality, lightweight, full flow hose end fittings for nitrile fuel hose. Nuke Performance offers a wide range of hose ends. With the AN lineup, you get a perfect solution for all types of fuels. Wide variation and in various sizes. Available in AN-4 / AN-6 / AN-8 / AN-10 / AN-12 For Nuke Performance Full-Flow AN fuel hose Full Flow hose ends for motorsports applications Straight / 30 / 45 / 60 / 90 / 120 / 150 / 180 degree Safe for all type of fuels, including ethanol The Nuke Performance Full Flow series offers AN hose ends and a premium black nylon race hose which is reinforced with a single braid of bright, corrosion-resistant type 302 stainless steel wire braid, and the black braided nylon cover makes this lightweight hose both durable and attractive. Safe for alcoholic fuels, but for long-time use you should look into the Nuke Performance Full Flow PTFE series with a much longer life span when used with alcoholic fuels such as ethanol.

Hammer Fab puffy script beanies LIMITED SUPPLY!

These -6 AN line clamps are designed for use with braided fuel lines, as well as for mounting cables, tubes, and wire harnesses. Featuring 1/4-20 socket cap fasteners, they provide a secure and durable solution for managing loose ends.

Do you need your 4th Gen F-Body instrument bezel repaired? Got broken tabs? We have a couple of solutions for you that won’t break the bank. 1) We developed some repair parts made from ABS plastic that you can buy and install yourself with CA clue (included) and a small torch, or….. 2) You can mail us your instrument bezel and we can repair the broken tabs for you and ship it back to you, ready to install. (Selecting this option is for the deposit only, final quote will be determined per job) 3) If your instrument bezel needs more than just repairing the broken tabs we can also fix cracks, refinish to factory appearance, custom paint, vinyl wrap, or upholster your bezel to the color of your choice (Selecting this option is for the deposit only, final quote will be determined per job)

PRE-ORDERS - please allow 4-6 weeks for delivery. These parts are made to order. Discover a modern solution to replace weak and outdated Third Gen F-body spindles. Say goodbye to inferior bearings and brake adapter issues. Our new Billet spindles are crafted from solid 6061-T6 aluminum, providing unbeatable strength and a one-stop solution for upgrading your big brakes. And when we say big, we mean ZL1-1LE BIG! These spindles also accept 2019 ZL1 Camaro sealed bearing hubs, maintaining the stock track width for your third gen f-body. They're compatible with both stock and aftermarket struts, and can even achieve a "wide body look" with our optional 1/2" hub spacer. With the ability to bolt on ZL1-1LE wheels or other modern billet wheels, you'll never have to worry about stopping power or bearing maintenance again. Plus, each spindle includes a billet steering arm made of aircraft grade 7075-T6 aluminum, ensuring the same steering geometry as an original third gen f-body. (NOTE): Hubs come with a 5x120 mm bolt circle, 14mm x 1.5 studs, and fit a 67.1 mm center bore. Will accept 6th gen Camaro SS brakes (18” wheels or larger required) Will accept 6th gen ZL1 1LE brakes (19” wheels or larger required)

Facing the challenge of installing an LT4 supercharged engine into a Third Gen F-body? Our LT4 Throttle Body Angle Correction Plenum is the perfect solution, expertly designed to align your throttle body with the factory IROC style intake plenum duct. Made from durable Carbon Fiber Nylon, this kit includes four 6mm x 30 bolts for secure attachment to your supercharger. Simply use your original style O-ring gasket and a flat gasket (not included) on the respective sides. Tapped threads are provided on the throttle body side for M6 bolts (not included) to attach your throttle body. Also comes with rubber 45 degree flexible elbow with clamps. (NOTE) this kit is only guaranteed to work with clamshell style engine mount kit from Hawks Motorsports. Part # SKU:HM-8492LTXMM-KIT (NOTE) Engine angle may also affect the alignment of this part. Our test car had the TR6060 raised about 1.5” and tunnel was cut to achieve more ground clearance, this tilting this plenum downward a bit in the front (hardly noticeable).

This textured switch plate is specifically designed to replace the ash tray in the center console of your 4th Gen F-Body. It features a Rockford Fosgate Bass volume control knob and an accessory toggle switch (sold separately) and can be purchased either bare or with the bass knob. The plate is secured with a small amount of double sided tape and does not require any cutting or modifications. Rest assured, the lid will close completely with this switch plate in place. Also available as a blank with no holes.

Why waste valuable time creating your own bulkhead brackets? We understand the struggle of constantly making them for each hard line fuel system. That's why we offer a more efficient solution. Our A/N bulkhead brackets are expertly crafted from 304 stainless steel, precision-cut and bent with pre-drilled holes for effortless installation on your chassis, firewall, or body. No painting required - simply bolt it on and you're good to go! Choose from single or double configurations for -6 and -8 AN fittings. -6 for fuel vent as pictured

New Arrival! Don't miss your chance to be one of the lucky few to own the exclusive Street Connection Suspension T-shirts by Hammer Fab! With a limited edition design and two color options, these t-shirts feature a multi-color printed design on the back and a new retro Hammer Fab logo on the chest. But hurry, once they're gone, they're gone for good! Available in a range of adult sizes, the Gildan 64000 Softstyle T-Shirt is the perfect blend of comfort and style, making it the perfect canvas for custom Hammer Fab designs. Made with soft and lightweight cotton, this t-shirt boasts a modern fit that is perfect for everyday wear.

These are the best quality made in the USA dimple dies available. These four crater maker dies are CNC machined from 4140 alloy steel, heat-treated for hardness, Sizes are #10, 1/4", 5/16" and 3/8". The #10 uses a dowel pin to align the dies while the others use threaded bolts. The 5/16 and 3/8 bolts can be used to draw the dies together however this hardware is not meant to last forever. We recommend using the provided hardware as alignment pins or starting bolts and finishing the operation with a large bench vice or hydraulic press. The Crater Makers require a lot of force, much more than some of our other dies. Use Anti-Seize or other lube to prevent galling of threads and dies!

Why waste valuable time creating your own bulkhead brackets? We understand the struggle of constantly making them for each hard line brake system. That's why we offer a more efficient solution. Our A/N bulkhead brackets are expertly crafted from 304 stainless steel, precision-cut and bent with pre-drilled holes for effortless installation on your chassis, firewall, or body. No painting required - simply bolt it on and you're good to go! Choose flat or bent 90 for versatility

Introducing Hammer Fab’s Professional Sanding Blocks — “Best Blocks” Starter Set – Flexible Hard Blocks (1/8” HDPE - 3 Blocks) This three-piece kit is the perfect entry point into Hammer Fab’s premium sanding system. Each block features a 1/8” HDPE base for unmatched flexibility while maintaining a laser-straight sanding surface. The CNC-machined 1” EVA foam handle provides comfort and controlled grip, with each block size clearly marked for easy identification. Includes 6”, 10”, and 20” lengths — the go-to tools for high-end body and paint work where flawless results matter most. Proudly made in the USA by real craftsmen. Starter Set – Semi-Rigid Hard Blocks (1/4” HDPE - 3 Blocks) This three-piece kit delivers the next step in sanding precision. Each block is built on a 1/4” HDPE base, offering a semi-rigid profile for a firmer sanding experience while still maintaining subtle flex. The CNC-machined 1” EVA foam handle ensures comfort and control, with each block size clearly labeled for quick identification. Includes 6”, 10”, and 20” lengths — designed for body and paint professionals who demand a straighter cut and tighter surface control. Proudly crafted in the USA by real craftsmen. Combo Set – Flexible + Semi-Rigid Blocks (1/8” and 1/4” HDPE - 6 Blocks) The best of both worlds in one kit. This six-piece collection combines the flexible 1/8” HDPE blocks from Set 1 with the semi-rigid 1/4” HDPE blocks from Set 2, giving you the complete range of control for any body or paint job. Each block is topped with a CNC-machined 1” EVA foam handle for comfort and precision, with all sizes clearly marked for easy identification. Includes 6”, 10”, and 20” lengths in both flex and semi-rigid versions. Proudly made in the USA by craftsmen who understand what perfect surfaces demand.

Battery Relocation Bracket & Tray for Third Gen F-Body 82-92 Camaro Relocate your Group 34 or 3400 series battery to your trunk with this precision laser-cut steel bracket and tray. The bottom-clamp design eliminates bulky top bars for a clean, OEM-style look, while the included template makes drilling and mounting in the spare tire well simple and accurate. This is a great way to add some weight to the back end of your otherwise squirrelly Camaro while cleaning up your engine bay. Available in raw steel or powder-coated satin black.

Learn the professional process of prepping for, and spraying a flow coat with Hammer Fab Academy. Taught by veteran painter Heath Henderson (32+ years in the industry), This FREE class talks you through the basics of what a flow coat is, and the steps required for success. Just add to your cart and hit "checkout"-This one's on us!

Learn the essentials of power hammering in this FREE online lesson from Hammer Fab. Levi and Hank cover machine setup, safety practices, die selection, and basic maintenance. Perfect for beginners or anyone wanting a solid refresher on the fundamentals. Just add to your cart and hit "checkout"-This one's on us!

This set includes the Rigid, Standard FLEX, and Ultra FLEX 3" Backer Pads. HammerFab designed these 3-inch backing pads for Roloc-style discs with several unique features. Our backers ensure your abrasive disc stays flat throughout use, unlike other brands that lose their shape over time. The FLEX Pads are made of durable, flexible rubber, yet still sturdy enough to maintain their form. These high-quality FLEX Backer Pads have passed multiple drop tests from over 12 feet — even while installed on an air tool. The Rigid Backer Pad is constructed of durable nylon, which keeps the disc perfectly flat. Features• Thin outer edge• Lightweight• 1/4" steel arbor that fits most tools

This set includes 7", 10", and 14" soft foam sanding blocks Take your bodywork finish to the next level with this 3-piece Soft Foam Sanding Block Set. Designed for precision shaping and contouring, these lightweight, flexible blocks deliver the perfect balance of stiffness and conformability—ideal for working on curved surfaces, subtle transitions, or high-build primer

The HammerFab Foam Shop Knee Pad delivers comfort, durability, and mobility in one clean package. Built from firm, high-density foam with a convenient grab-and-go handle, this pad won’t slip out from under you, and keeps your joints happy while you get the job done. Features• High-density foam construction for lasting support• Built-in carry handle for easy transport• Non-slip surface for stability on smooth or dusty floors• Lightweight yet rugged enough for shop use• Perfect for mechanics, fabricators, detailers, and DIYers

A clean, no-drill solution for mounting your amplifier in a 4th Gen F-Body. Made from CNC-bent, TIG-welded aluminum, this rack installs using factory holes and studs—no cutting, drilling, or permanent mods required. It mounts completely hidden under the factory rear panels and occupies the spare tire location, giving you a solid, stealthy place to mount your amps. Features Stealth Design: Sits fully underneath OEM panels for a factory-clean appearance. Rock-Solid Construction: CNC-bent and welded aluminum in a raw finish—ready to paint or powder coat. Optimized Layout: Two mounting surfaces for flexible amp positioning. Installer-Friendly: No interior modifications and no hardware guesswork. Amp Fitment Top Plate: Up to 6-3/4” × 8-5/8” Side Plate: Up to 6-3/4” × 13-1/2” Amp Mounting We recommend using 10-32 rivet nuts to mount your amplifier to the rack, but sheet metal screws can be used as well.